PCB Separators, PCB Off-cut Remover

PCB Separator MAESTRO 2 / 2M

Overview

MAESTRO 2 separates small amount and prototype series of PCBs fast and economically. The compact and stable aluminum frame requires only a minimum of space.

MAESTRO 2M (motorized)

Separates large numbers of PCBs without fatigue of the operator. The lower circular blade is driven by a motor. The PCB is fed between the circular blades where it is seized, transported and separated. Three different speeds can be selected. Especially useful for high packing density or thin edge stripes.

Technical Data:

Separation type
Component side: circular blade
Solder side: circular blade

Operation
MAESTRO 2: by hand
MAESTRO 2M: motor-driven

Separation speed 2M
100/200/300 mm/s

Separation length
15 – 300 mm

Mains voltage 2M
230/115 V~ 50 – 60 Hz

Earthing stud
Ø 10 mm

Operating temperature
10 – 35° C

Storage/transport temp.
-20 – 50° C

Humidity non-condensing
10 – 85%

Safety regulations
CE, FCC class 1

Weight
MAESTRO 2: 16 kg
MAESTRO 2M: 19 kg

Dim. H x W x D
330 x 195 x 620 mm

PCB Separator MAESTRO 5L

Overview

For automatic separation of PCBs with pre-sored groove

MAESTRO 5L is used most economically whenever large numbers of prescored PCBs need to be separated. The well-arranged control panel ensures easy operation. PCB panels with a maximum width of 310 mm can be separated by up to 11 circular blades simultaneously.  Configuration of the blades is adjusted to your individual PCB also the cover and the guide.
Sensors are used to monitor the separation process. The PCBs are placed either by hand or they feed automatically by a loading station. The machine can also be installed in an assembly line. The SMEMA interface is the standard connection for this use. New: every machine is automatically prepared for dust extraction and with cleaning brushes for rear-end conveyor. PCB panel widths larger than 310 mm on request.

Technical Data:

Separation type
Component side: circular blade
Solder side: circular blade

Operation
motorized

Separation speed
100 – 220 mm/s in 10 steps

Length of PCB panel
with light barrier activated: 100 – 570 mm
with light barrier de-activated: > 100 mm

Width of PCB panels
max. 310 mm

Width off-cut
min. 3 mm

Height of components
Component side: max. 30 mm
Solder side: max. 10 mm

Number of circular blades
max. 11

Width of PCBs
10 – 300 mm

Display
Separation speed
Separated lenght or numbers of PCB panels

Keys
Start, stop, reverse
Setting of separated speed

Monitoring
Detection of separation lenght
Accumulation in front of and behind the blades
Stop the end of the conveyor belt

Interfaces
Remote start/stop
SMEMA (round 14 pins)

Mains voltage
230/115 V~ 50 – 60 Hz

Operating temperature
10 – 35° C

Storage/transport temp.
-20 – 50° C

Humidity non-condensing
10 – 85%

Weight
63 kg

Dimensions with base frame
Height: 750 – 1000 mm
Width: 440 mm
Dept: 1100 mm

Off-cut Remover Hektor 2

Overview

Hektor separates milled PCBs carefully and fast. The offcut material is removed smoothly and precisely. The matrix consists of two parts. This ensures easy and cost-saving change of the blades. Compressed air is used for the separation process. The operating pressure can be set on the machine. When the foot switch is pressed, the off-cut is punched out. The off-cuts are collected in the collecting box. When the gate is opened the waste material can be extracted.

Technical Data:

Separation type
Punch blade

PCB thickness
max. 2.5 mm

Air connection
1/4"-plug-in coupler

Operating pressure
typical 4 bar

Mains voltage
10 – 35° C

Storage/transport temperature
-20 – 50° C

Humidity, non-condensing
10 – 85%

Safety regulations
CE, FCC class 1

Weight
2.7 kg

Dimensions H x W x D
170 x 220 x 255 mm

For more products from CAB please go to CAB Website.